Depuis Octobre 2008, le Tinytrak 4 a connu un beau developpement lui donnant la possibilité, d'ajouté un Affichage, et de l'utilisé comme tracker et Kiss TNC sans avoir à changer le Firmware v0.54 qu'il est maintenant possible d'installer grâce a un logiciel.

J'en ai profité pour tester le mien dans mon auto, et le brancher à mon nouveau AVMAP G5, car le nouveau Firmware supporte aussi la génération de waypoints, et est compatible avec les GPS, pouvant les accepter.

Le logiciel est en développement et les versions changent. Byon continue de le developper et les commentaires sur ses performances et les demandes d'ajouts, sont bienvenus. Abonnez vous au groupe Yahoo de discution si ça vous intéresse, vous y trouverez beaucoup d'information.

Vidéo du décodage.

2 Plugs de 2.5 mm

La Plug TMC du GPS Avmat Geo5

L'ordinateur opère avec le logiciel UI-View 32 et le TT4 en mode KISS

Les stations reçues par le TT4D sont affiché sur le GPS AVMAT G5 et dans UI-View

P300 - Set the Packet module to send 300 baud (rather than 1200 baud)
TXTDISP - Set to display sent incoming serial text
NODISP - Set to disable the display (which enables digital telemetry)
PPATHING - Set to enable proportional pathing
DMSDISP - Set to display seconds (DD MM'SS") instead of decimal minutes (DD MM.mmmm)
MICETMV - Set to transmit MIC-E format including type, manufacturer, and version
ENTS - Set the use of Time Slotting (use TSOFFSET)
TELHIRES - Set telemetry to send high-res data (0..999 ratehr than 0..255)
TELVOLT - Set telemetry to send the supply voltage
TELTEMP - Set telemetry to send the temperature
PREEMPT - Set Preemptive Digipeating
DIGIID - Set Digipeater to replace digipeater callsign with MYCALL
WXPOS - Set weather reports to include postion
TOSV - Set the tracker to only send valid position reports
TALT - Set the tracker to send altitude, if available
TIMESTAMP - Set the tracker to send a timestamp (format defined by TIMEHMS)
TIMEHMS - Set the tracker to send a timestamp in Hour, Minute, Second format (rather than Day, Hour, Minute)
SBEN - Set to enable tracker SmartBeaconing (Use other SB commands to configure)
TSWPT - Set the tracker to output a GPS waypoint of self when position is transmitted
AMODE - Set the Primary serial port mode [ KISS | TEXT | GPS | DEAFTEXT ]
BMODE - Set the Secondary serial port mode [ KISS | TEXT | GPS | DEAFTEXT ]
ABAUD - Set the Primary serial port baud rate
BBAUD - Set the Secondary serial port baud rate
SSIDROUTE - Set the SSID routing mode
ALTNET - Set and alternative network destingation
MYCALL - Set the Packet source (user) callsign with SSID
DIGI1 - Set the outgoing digi path first callsign
DIGI2 - Set the outgoing digi path second callsign
DIGI3 - Set the outgoing digi path third callsign
PPATH1ST - Set the proportional pathing first callsign
PPATH2ND - Set the proportional pathing second n-N callsign
TSTATUS - Set the tracker status text
BTEXT - Set the beacon text
BPERIOD - Set the beacon period in seconds
TXD - Set the Packet Transmit delay time in bytes (about 7ms each at 1200 baud)
PERSIST - Set the Packet Persist value. (0 to 255, higher is more likely to transmit)
SLOTTIME - Set the Packet Slottime
QUIET - Set the Packet delay after carrier detect drops before a transmission can occur (in 100ms units)
CDMODE - Set the Carrier Detect Mode
CDLEVEL - Set the Carrier Detect Level (applicable to Audio Level and Audio Tone methods)
TXLEVEL - Set the Packet transmit audio level (0 .. 128)
TXTWIST - Set the Packet transmit audio twist (0 = all low tone, 50 = even tone levels, 100 = all high tone)
RXAMP - Set the Packet recieve audio amplifier
GWAYLEN - Set the GPS Waypoint output name length
GWAYMODE - Set the GPS Waypoint mode
GRELAYBITS - Set the GPS Relay Sentence Type Bits
GRELAYRATE - Set the GPS Relay Rate (0 = disabled)
LOCATION - Set the default location (in the form ddmm.mmmmx dddmm.mmmmx
GALT - Set the default location altitude
TSYMCODE - Set the tracker Symbol code character
TSYMTABLE - Set the tracker Symbol table or overlay
STATUSRATE - Set the tracker Status Rate (0 for never, uses the TSTATUS)
PPERIOD - Set the tracker Position report period in seconds
SBSSPEED - Set the tracker SmartBeaconing Slow Speed (Use TSB to enable)
SBFSPEED - Set the tracker SmartBeaconing Fast Speed (Use TSB to enable)
SBSPERIOD - Set the tracker SmartBeaconing Slow Period (Use TSB to enable)
SBFPERIOD - Set the tracker SmartBeaconing Fast Period (Use TSB to enable)
SBTANGLE - Set the tracker SmartBeaconing Turn Angle Speed (Use TSB to enable)
SBTSLOPE - Set the tracker SmartBeaconing Turn Slope (Use TSB to enable)
SBTTIME - Set the tracker SmartBeaconing Turn Time (Use TSB to enable)
MICEMESSAGE - Set the tracker MIC-E Message number
TSOFFSET - Set the tracker Time Slot Offset (Use ENTS to enable)
TDAO - Set the tracker !DAO! resolution (0 for disabled, 1 for 1 extra digit, 2 for 2 extra digits)
TPROTOCOL - Set the tracker output protocol (MIC-E, APRS Text, Compressed)
TPERIOD - Set the telemetry report period in seconds
WPERIOD - Set the weather report period in seconds
ALIAS1 - Set the digipeater alias callsign with SSID
ALIAS2 - Set the digipeater alias callsign with SSID
ALIAS3 - Set the digipeater alias callsign with SSID
DUPETIME - Set the digipeater alias callsign with SSID
FILTERCALL - Set the callsign to filter match
QUIT - Quit the options menu
DISPLAY - Display all option values and commands
HELP - Display help for all options and commands
RESTORE - Restore default factory settings
MONITOR - Monitor incoming audio level
CALIBRATE - Calibrate transmit audio level

J' utilise le logiciel TERMINAL pour communiquer avec le Tinytrak4 à 19,200 bauds 8,N,1 pour en modifier les paramêtres

On branche tout et lorsque l'on met sous tension un ? apparaît, on doit presser ESC 3 fois rapidement.

Ci-contre la liste des commandes qui apparaît lorsque l'on tappe la commande HELP

:disp

P300 is FALSE
TXTDISP is FALSE
NODISP is FALSE
PPATHING is FALSE
DMSDISP is FALSE
MICETMV is FALSE
ENTS is FALSE
TELHIRES is FALSE
TELVOLT is TRUE
TELTEMP is TRUE
PREEMPT is FALSE
DIGIID is TRUE
WXPOS is TRUE
TOSV is FALSE
TALT is TRUE
TIMESTAMP is TRUE
TIMEHMS is TRUE
SBEN is FALSE
TSWPT is TRUE
AMODE is KISS
BMODE is GPS
ABAUD is 4800
BBAUD is 4800
SSIDROUTE is 0
ALTNET is APTT4
MYCALL is VE2WMG-10
DIGI1 is WIDE1-1
DIGI2 is WIDE2-2
DIGI3 is
PPATH1ST is
PPATH2ND is
TSTATUS is 147.240 t103.5
BTEXT is qso 442.700 t103.5
BPERIOD is 300
TXD is 30
PERSIST is 65
SLOTTIME is 15
QUIET is 10
CDMODE is LEVEL
CDLEVEL is 8
TXLEVEL is 128
TXTWIST is 50
RXAMP is 12
GWAYLEN is 9
GWAYMODE is NMEA
GRELAYBITS is 1
GRELAYRATE is 0
LOCATION is 4539.3600N 07233.6500W
GALT is 65
TSYMCODE is O
TSYMTABLE is /
STATUSRATE is 1
PPERIOD is 60
SBSSPEED is 5
SBFSPEED is 60
SBSPERIOD is 1800
SBFPERIOD is 90
SBTANGLE is 27
SBTSLOPE is 255
SBTTIME is 5
MICEMESSAGE is 0
TSOFFSET is 17
TDAO is 2
TPROTOCOL is APRS
TPERIOD is 120
WPERIOD is 300
ALIAS1 is
ALIAS2 is
ALIAS3 is
DUPETIME is 30
FILTERCALL is

:quit

A gauche, mes paramêtres pour vous guider et que l'on obtient avec la commande DISP (display),

Il faut pour podifier un paramètre tapper la commande, avec un espace et la nouvelle valeur